gtp error(pls help)

[anilkumar]

hi guys

when iam doing GTP  error coming .

please help me out , find  an attachement

regards

Anil Kumar

[kulkarni]

Were you able to fix this?  Do you know what was causing this?  Is there a workaround for this error?

[satay2hot]

CHECK YOUR ELIST AGAIN

Make sure the subtotal doesnt is recurring in another elist

[kulkarni]

Hello satay2hot,  can you please clarify a bit more on what you said?  Are you saying a 'subtotal' d-list item should not be part of another d-list?

[amitbehere2002]

Hi Mr. Anil Kumar

Can you try the following Solution
 
Error executing J expression : 'ACE2_rc ACE2_xids ACE2_Package' =: Pack 90 error running GTP
 
     (1)
 Technote (troubleshooting)
 
Problem(Abstract)
When GTPing, the test reconcile step fails with a pop-up dialog box containing the message below
 
 
Symptom
Dialog Box:

The Go To Production process failed.

Unable to reconcile 'elist'

Exception encountered when working with model.

Error executing J expression : 'ACE2_rc ACE2_xids BlockPackages' =: 90 ReconcileBlocks_IModelEdit_NodeGuids;OldBlockPackages;<PackageFormat

PlanningErrorLog:

Error executing J expression : 'ACE2_rc ACE2_xids ACE2_Package' =: Pack 90
 
 
 
 
 
Cause
Contributor cannot compare the development and production versions
 
 
 
Resolving the problem
Reset the production version to development

Steps:

In the admin console, reset the production to development (button on the top of the console)
Create, save and remove an access table (in order to force a reconcile job)
Run GTP again
 
Another Solution which i found on IBM Site is

During GTP: Error executing J expression : 'ACE2_rc ACE2_xids ACE2_Package' =: Pack 90
 
 Technote (troubleshooting)
 
Problem(Abstract)
When GTPing, the test reconcile step fails with a pop-up dialog box containing the message below 
 
Symptom
Dialog Box:
The Go To Production process failed.

Unable to reconcile '416_acd_skn'

Exception encountered when working with model.

Error executing J expression : 'ACE2_rc ACE2_xids BlockPackages' =: 90 ReconcileBlocks_IModelEdit_NodeGuids;OldBlockPackages;<PackageFormat

PlanningErrorLog:

Error executing J expression : 'ACE2_rc ACE2_xids ACE2_Package' =: Pack 90
 
 
 
 
 
Cause
Largest cube too large 
 
 
Resolving the problem
Split the largest cube into 2 
 
 

[anilkumar]

Thank you for all responding.
 i resolved error

[anilkumar]

hi Amitbhere

can i have u  r mobile no so that i wanna discuss more things.

i am expecting ....

Thanks and Regards
anil

[amitbehere2002]

1

[kulkarni]

Thank you for all responding.
 i resolved error

Can you please explain how you fixed this error?  Thanks.

[anilkumar]

HI kulakarni
i have done workaround,


1)i created new model
2)split the  cube

Thanks & Regards
Anil Kumar

[wentriken]

I have the same error: ace2_rc ace2_xids ace2_package pack 90

But it is caused by a different circumstance.

I have created a new model in Analyst and and creating the Contributor application. Now when I go to Dev/Elist and add an item and save, I get this error.

I have never run GTP before, because this is the first time I am adding an elist. My largest cube is 500,000 cells.

Any ideas?

[jeffowentn]

What does the planningerrorlog.csv (from the CAC > Tools > Show Local Log File) show?  This will likely be more helpful.

Did you modify the elist in the GUI interface in the CAC, itself, or did you export/import using a flat file or Excel file?